Orbis-Spokeless Wheel

prototyping

Spokless wheel Prototype

 

Happy New Year! As some may already know, I have been heavily involved for the last few years in what is now called ORBIS. We originally set out to solve a problem with poor electric bike hub motors but this has evolved into an incredible technology that I believe will change the world of powered, wheeled vehicles. I really cant share too much information as we are Patent Pending.  I am willing to say that in 2016, we plan on our first product launch with out technology. I will keep you posted.

The past year has been challenging and extremely fun creating prototypes of a motor bike, wheelchair and more to come. This photo is Levi, my 12 year old son trying the PiMoto out. Stop by the shop sometime to see what we are working on, perhaps you have an idea I can help bring to life!

Call or email any time for a free consultation.

scott@trueformdesign.com

888-405-4445

CUSTOM FIRE PLACE SURROUNDS

2015-08-20 17.39.22

A FINISHED CUSTOM METAL FIREPLACE SURROUND

2015-08-20 15.33.20

CORNER RADIUS WELDING, ugly now, but it will all disappear soon…

2015-08-20 15.33.35

BOTH SURROUNDS ALL FIT UP, READY FOR WELDING

2015-08-20 15.33.49

A WELDED CORNER READY FOR “CLEAN UP”

 

 

 

2015-08-20 17.38.54

WELDED, CLEANED UP SURROUND,READY FOR FINISH

 

2015-08-20 17.39.08

SAME CORNER, AFTER CLEAN UP

 

 

 

 

 

 

 

 

 

 

 

 

What can you do if your brick fireplace needs a new look?

Metal fireplace surrounds are a sure fire way to make your room look completely different. I made these for some dear friends who have a dinning room and living room fireplace on the same wall. They had a pretty good idea of what they wanted when we started designing. One constraint was a 3/4″ radius all around. This is to match the custom concrete work that these metal surrounds will rest on. The construction is 1/8″ CRS plate. This material lends itself to clean, sharp looks. The formed radius on all the corners gives a uniformed, machined look to it. The only problem when doing this, is that the edge that returns to the wall is a welded edge, not formed like the rest. Getting this joint to match the others is the real challenge. My designer suggested cutting a section from a tube and welding iot into place for the radius. This worked well and took less time than I expected. For the two full radeus corners, I cut a metal ball into sections and fit it in to accept both radii. This is one of those jobs that “clean up” , meaning grinding, polishing and “hiding” the weld takes about 10x more time than the welding itself. The whole unit attaches to the wall via keyhole slots welded to the back edge of the structure. The second challenge of this job was the finish. I was given a picture frame from their home to match the color and finish. This is the topic of its own post later…..

                                                                                                                   Need to bring your Living room into the 21st century too?

 

 

 

 

/

AWARD WINNING FUNCTIONAL ART

 

 

AS SEEN AT THE SAUSALITO ART FESTIVAL!

 

 

custom fabrication, upcycled

OVAL TABLE BASE WELD CLEAN UP

CUSTOM TABLE, FABRICATION

TABLE BASE READY TO SHIP TO SF FOR WOOD TOP INSTALL

 

 

 

CUSTOM METAL FABRICATION

OVAL TABLE DISPLAYED AT SAUSALITO ART FESTIVAL

FIRST PLACE AT SAUSALITO ART FESTIVAL

FIRST PLACE FINISH , SAUSALITO ART FESTIVAL , FUNCTIONAL ART

 

 

I have been blessed for years to have the privilege working with Daniel Krivens. We first met when he needed help dismantling riveted beam sections from the old Golden Gate bridge approach. I think we may have done some Bay Bridge parts as well. Daniel is truly an artist who sees the beauty in the discarded, rusted, bent and abandoned municipal structures. Weather he is building a coffee table out of a split fire hydrant, or a dining table from Bay Bridge supports, his eye is trained to see more than scrap metal. Recently I was able to help with a new metal fabrication to form a table base for Daniel. Once I shipped the TIG welded steel base to his shop in SOMA, he graced it with beautiful found wood tops in the shape of a propeller. The wood came from a stash of Transbay piling beams that Daniel has transformed into gorgeous shaped tables. The pilings were huge and quite old so the grain structure is extremely dramatic. Please check out his site, super interesting! http://www.krivens.com/ Poke around on his site and you will see several items I have fabricated. I love working with Daniel because his art mixes clever strength and simplicity  while remaining sharp. The contrast of materials always invokes interest especially when you find out what they are from…There is more to come from Daniel Krivens very soon!

 

Now, go purchase some functional art!

http://www.krivens.com/

There’s always a better way….probably 10.

better-mousetrap-pc-750x600-enlarged

 

Build a better mouse trap…world beats a path. etc, etc… I hope its true. One thing I know is true…there is always a better way…. I have come to make this my mantra when developing, inventing, problem solving. Every time I use this powerful little tool, It works for me. In his book, The Lean Startup, Eric Ries describes the concept of the 5 whys. I believe it was originally from the Toyota Manufacturing playbook. As I understand, to plat this game, at least 5 why? must be asked, or until it is completely clear what the  original issue is, only then can a problem be solved. Otherwise, only symptoms are managed. In the following scenario Eric writes, a fuse was replaced several times before the 5 Whys were employed.

5 whys

 

I have found this so helpful. Not only in machine repair, but in the creative process. Where the 5 Whys dig into a problem to reveal a clear solution, I believe The 10 Ways can build up a platform of ideas one can employ to create, not only solve a problem. I have used this many times. I think it started when I was in a group of fabricators trying to solve a serious “painted yourself into a corner” problem. Ok, here is the scenario; We had built a huge Plastic pellet mixing, drying unit. Seriously big. It consisted of a Jacketed body roughly 100″ in diameter and 25 feet long. Inside the body, rotated a huge Rotor. The rotor consisted of a special custom “pipe” with 96″ diameter Stainless Steel discs welded so that about 50 of these discs set 4″ apart rotate. There are Stainless Steel arms that bolt to the side of the body and scrape the plastic material off the discs as they rotate.

Drying-top

 

Above is a picture of a 36″ unit, unpolished. Now, the rotor was too heavy to ship in the body but the client insisted the mixing arms needed to be installed so they would not be scratched during shipment over seas. The problem was that the particular unit we built was completely polished inside and was an end load unit, meaning there was no top to remove for access. The rotor had to be installed through the one open end. But all we had to do was install the mixing arms in the 25′ long body. No problem right? Standing there with the other journeyman guys as an apprentice, I was interested to see what the procedure would be to get all these arms installed. The mounts were at lease 10′ high and unfortunately, the bottom of the body was a trough, no flat surface, and polished to a shine. All attempts were embarrassing to those who tried to lift one of these 60-70 pound arms up to the mounting screws. I remember one guy there just threw up his arms and said,”it just cant be done….”. I guess they had no procedure for this type of problem.  Being the young apprentice, and a class A smart allic, I quipped,” oh, there are at least ten ways to get this done…”. The remark was met with lots of laughter obviously. But, as an exercise, I started listing them.

OK guys, we can;

•place cardboard down on the bottom and just walk to the back and lift them up to the mounting studs-oops, too heavy

•ok, we use two guys to help lift them up- oh no, once we got the part up and started for the wall,the cardboard just slid out from under us and we would drop everything while sliding back to the center of the body trough.

•Hey, we can cut a 2×12 just the right length so we can step out on it, that way we don’t have to raise the arms up so high and we can have a flat surface to walk on.- the board holds until it doesn’t, throwing me and the arm straight back to the floor.

•Ok, this time we will counter weight the two guys with a 2×4 from the platform to the top of the unit.- unfortunately, the top was rounded too so there was nothing for the 2x to bump ageist.

• what if we rig up a counterbalance on a spreader bar hanging from the crane and ten using the crane, side it in? - close but still no way to control it enough to line up the 4 studs and get nuts on them. but… this lead me to another idea.

•ok, I got it now, we load up the Snorkel man lift basket with the tools and an arm. then, using the telescoping arm, travel into the unit without touching the bottom or sides.

 

Using this technique, we quickly loaded all the arms, safely and with out scratching up the fine surface (anymore). Maybe it wasn’t a full 10 ways, but using this method got the job done in a way none of the “journeymen” guys had ever thought of.

I continue to use this to open my mind up. Every time someone tells me that there is only one way to get a job done, I love proving them wrong. There is always a better way, in fact probably 10 ways. What ever issue or problem you are working through, I bet if you stop and think of 10 ways to solve it, you will find one that works better than the one you are using now.

 

BRING YOUR IDEA, I’LL MAKE IT HAPPEN

2015-11-19 10.07.54

Fixture Plate for Laser Engraver

2015-11-20 15.14.08

complete Fixture Plate

 

Custom Fixture Plate

I love working on custom parts. One of my affiliates that does my laser etching came to me with an idea for a fixture plate to add to his Laser machine. This will enhance the table size by about 200% as well as ensuring great accuracy and speed up set ups. By using precision pins in reamed holes, we can create walls and stops for parts to “lock” into. This will save a lot of time when repeat parts are changes in and out of the machine for engraving.

This is typically how these types of jobs come about; someone has an idea that will make their lives or job better. The problem is, there is a gap between the idea and the execution of that idea. This is the gap I live and work in. I may not be the only one that can bridge this “gap” but I can promise you this; I am your best choice. Here is why;

○ with my background in the bicycle industry I have a constant eye on form ( ascetics), function and fit.

○ my food and chemical industrial equipment background at BEPEX, where I earned a journeyman card in metal fabrication taught me the systematic procedures for construction, finish, efficiency in manufacturing and industrial design.

○ managing Bulldog Machine Inc, where I received a machinist journeyman card after a 4 year apprenticeship, I learned project management, sourcing, networking, customer service, large part machining, cutting edge manufacturing practices among many other skills that add value to my clients now.

○ Now that my own shop is up and running, I can provide immediate help with design and rapid prototyping.

○ I care.

What could utilizing all my resources allow you to create?

Store is open

open

Yes, the store is now open.

Just click on the SHOP button and order your cool bottle openers, interesting candle holders, vases, etc.

You cant get this stuff at Target.

Thanks!

http://trueform.myshopify.com/

RIM RING Bottle and Can opener

2015-08-06 14.48.44

 

Kickstarter is LIVE!

https://www.kickstarter.com/projects/110500571/rim-ring-the-bike-rim-bottle-can-opener-and-keycha

Back often, Back strong!

Ava, my daughter and I completed this campaign in roughly one afternoon. Its really a test to see how the system works and to test out this product. If this goes well, I have about 40 ideas I want to try. If you are in the bike industry, like to ride or just need to open some cans or bottles, check out the link please. I really appreciate it!

PASS it ON!

Kickstarter sneek peek

 

 

 

2015-08-06 14.48.44

 

 

RIM RING , the bike rim bottle opener/keychain

 

 

Ava, my second daughter and I spent one afternoon to come up with a kickstarter campaign for a little product I have been prototyping for months. Literally this took a few hours one evening and a few hours yesterday. I am going with the MVP approach to product development here. Please check out this test page and offer any suggestions to the campaign before we go live. Please click on the link to view and comment.  Thanks so much!

https://www.kickstarter.com/projects/110500571/1231712285?token=2219f09c

Trueform Office

2015-08-07 09.21.512015-08-07 09.22.07

2015-08-07 09.22.25

 

TRUEFORM OFFICE NOW OPEN

 

FINALLY! I finally have wifi at the new Trueform Shop. I spent a part of yesterday morning setting up the office space. I have adopted a stand up desk for office work. I think it helps with productivity and adds more movement to my day. My desk is a Harbor Freight Special but I love it. I though you might like a few shots of my new office. I’m sure its not like many you have seen. I guess this is due to the fact that I really don’t have an office job…. While more and more work is done through computers, I am really a machinist. I can take three steps and I am at my workbench, mill, welding table,etc. This meager office area provides exactly what I need for the design, project management, research, purchasing and communication elements of my business. I hope you can come visit soon to see it in person. Take me up on my offer and Ill provide the hot or cold drinks…. See you soon.

 

3200 Dutton Ave

#220

Santa Rosa, CA

95407

 

888-405-4445

Portable Sales Display

stainless pipe display

custom display

2015-06-12 17.27.28 HDR

 

My old friend, Jim Passey is a sales rep for Krausz USA, a pipe coupling company. Jim needed a mobile way to display some of the products Krausz sells. This way he can take a “mobile showroom” to the people that need to see them. Jim had a basic idea of what he wanted. We met to brainstorm some ideas of a display that would slide into his truck but be able to be removed easily. Jim decided on a handful of products to showcase, we measured them up and designed a way to hold them at eye level for display. The frame is made of stainless steel with a light grain polish. This finish will last forever and if scratches do occur, a quick sand will hide them. The beautiful stainless looks great against the bright blue of the products too. The last element is the Krausz Logo sign.

Custom designed displays like this can be extremely valuable for all types of products. I would love to work with you on your next display!